Find the water first, then the mold
When a room smells like a damp cellar but every surface looks clean, moisture is hiding behind a finish. The dispatcher connects you with a licensed and insured independent inspector in Alamo who finds the wet spot, the cause and the scope, and puts it all in writing.
ESS Mold Inspection is a free referral line. Every inspection is performed by an independent local contractor, never by the line itself.
What an inspection actually is
A good inspection is an investigation of the house from top to bottom, and it should never feel like a pitch. The inspector walks the property room by room, looks at ceilings, baseboards, window sills and the backs of closets, and takes moisture readings along the way. A pinless meter gets swept along walls and floors to find wet zones fast, then a pin-type meter confirms the number at the suspect spot by pressing two short probes into the material. Those readings get plotted on a sketch of the floor plan, which is what people in the trade call moisture mapping.
An infrared camera doesn't actually see mold. It shows temperature differences, and wet drywall or insulation usually reads cooler than the dry material around it, so a cold streak under a window tells the inspector exactly where to put a meter. A hygrometer gives relative humidity and dew point for each area. If the dew point sits close to the surface temperature of a wall, a duct or a window frame, condensation is forming there. When something looks suspicious inside a wall cavity, many inspectors drill a hole about the width of a pencil and look in with a borescope rather than opening up the drywall.
The step most people skip is the one that matters most: finding where the water comes from. If the leak, the condensation or the drainage problem stays, any cleanup is temporary. That's why the inspector checks the HVAC air handler, the evaporator coil, the condensate drip pan and drain line, the attic decking and vents, and the crawl space vapor barrier and joists, not just the room that smells. Homeowners around Alamo call this line when they're buying a house, after an old leak, or when a musty odor keeps coming back and nobody can explain it.
What you should expect
An inspection is only as good as the person holding the meter, so the line routes calls to inspectors who investigate first and have nothing to sell you afterward.
Every inspector the line routes to runs an independent business with liability coverage and any state mold assessor license that applies. Some states also bar the company that writes the protocol from doing the remediation on the same job, and even where it's legal, keeping them separate means nobody profits from inflating the scope.
Inspection calls are rarely emergencies, but real estate deadlines are. Mention your closing or contingency date on the call and the dispatcher prioritizes inspectors around Alamo who can get out soon; same-day is common for an active leak.
Inspection pricing usually depends on square footage, the number of areas, and whether attic and crawl space access is needed. You get the price before anyone arrives, and if lab samples might be added on site, ask how they're billed per sample before the visit.
Expect pin-type and pinless moisture meters, an infrared camera, a thermo-hygrometer, a borescope and a strong flashlight, plus a ladder for the attic hatch. If the person who shows up carries a swab kit but no meter, that's not an inspection.
Inspection types
Tell the dispatcher why you're calling, because a pre-purchase walkthrough and a hunt for a hidden odor are not the same visit.
This one is timed to your contingency window and focuses on the signs sellers sometimes paint over: ceiling stains, swollen trim, a rusty water heater pan, white mineral bloom on foundation walls.
When a smell shows up but growth doesn't, the inspector follows the odor room by room, scanning plumbing walls, laundry areas and exterior corners for cool, damp spots.
A clogged condensate line or a pan that never drains can feed growth on the evaporator coil and inside the air handler cabinet, then push that odor through every supply register.
In the attic, the inspector looks for dark staining on roof decking, frost or condensation on nails, blocked soffit vents and bath fans that dump air into the insulation. Under the house, the checks cover wood moisture in joists and sill plates, the condition of the vapor barrier, and any pooling water.
Once remediation wraps up, a separate inspector confirms the work matches the written scope, from dry readings on the studs to an undisturbed containment barrier and a fixed leak. Lab clearance can be added if you need it, but the visual and moisture verification comes first.
One call puts you in touch with an independent, licensed inspector in Alamo who maps the moisture and explains what's behind the finish.
How it works
From the first call to the written report, here's what the process looks like.
The dispatcher asks why you need the inspection, how big the home is, whether there's an attic or crawl space, and if there's a real estate deadline.
An independent inspector near Alamo confirms a time, and same-day visits are common for active leaks. Clear access to the attic hatch, the air handler and under sinks before they arrive.
Room by room, the inspector takes meter readings, runs thermal scans, records humidity and dew point, and works through the mechanical systems. If extra work like sampling comes up, you see the cost first.
The final report lays out photos, readings, the cause and a protocol, so remediators bid on the same scope.
From the dispatch log
A few patterns show up on the line over and over.
A homeowner called about a musty smell that got worse every time the air conditioning kicked on, with no visible growth anywhere. The inspector found the condensate drain line clogged with slime, the drip pan overflowing, and wet insulation inside the air handler cabinet. Thermal imaging showed a damp patch on the closet ceiling below.
Outcome: The report pointed to the drain line and air handler, not the bedrooms, so cleanup stayed small and focused.
With less than a week before the contingency deadline, a buyer called because a single ceiling had suspiciously fresh paint. The inspector's pinless meter found elevated moisture under the paint, and a borescope through a small hole showed staining on the back of the drywall from a leaking shower valve above.
Outcome: The buyer used the written report to negotiate a repair credit before the option period closed.
A condo owner called after the unit upstairs had a dishwasher leak that the association said had been dried. Weeks later the kitchen ceiling had a faint ring. Moisture mapping found the wet area ran past the ring, and the dew point readings ruled out condensation as the cause.
Outcome: The report documented the extent of the moisture so the owner had evidence for the association and insurance.
A parent reached the line after months of stuffy noses that seemed to ease whenever the family traveled. Room humidity sat near 70 percent. The inspector found a crawl space with a torn vapor barrier, damp joists, and gaps letting crawl space air into the return duct.
Outcome: The scope covered the vapor barrier, air sealing and humidity control, and the family took the report to their doctor.
These are composite examples based on common calls to the line, not individual customer reviews.
Questions
Call the line and get routed to an independent, licensed inspector near Alamo.
Call +1-844-326-4757An inspection is the investigation: the inspector walks the building, maps moisture, scans with thermal imaging and figures out why mold is growing and where. Testing is narrower and means collecting samples for a lab. Plenty of inspections never need one, because visible growth plus a wet reading already tells the story.
For a typical single-family home in Alamo, plan on two to three hours on site. Add time for a large footprint, a hard-to-reach crawl space, extra air handlers, or several spots that need a borescope look. The written report usually follows within a day or two.
Usually not. Moisture meters and an infrared camera work from the surface, and when the inspector needs to see inside a cavity, the standard move is a small drilled hole for a borescope. Anything bigger should be discussed and approved by you first, and in a rental, by the owner.
It's the cleaner setup, yes. When the company that finds the mold also gets paid to remove it, there's an obvious incentive to write a bigger scope. Some states prohibit one company from doing both on a single job, and even where it's allowed, a separate inspector gives you a scope you can take to several remediators.
No rule requires one, though it makes sense when the listing or the general home inspection hints at water, like stains, a sump pit or a musty lower level. Schedule it right after your offer is accepted, so you have the report while you can still renegotiate or walk away.
A useful report has photos of each problem area, moisture readings and where they were taken, humidity and dew point by room, and thermal images with notes. The part you'll use most is the protocol, which spells out what to remove, the containment and air filtration, the moisture repair, and how the finished job gets checked.
Service area
The line routes inspection calls throughout Alamo, from older homes with plaster walls and original ductwork to newer builds with tight envelopes that trap humidity. The dispatcher matches you with a nearby independent inspector who works separately from the cleanup side.
If you're under contract, mention the deadline first. For an active leak, shut off the water if you can and call the line so a local inspector can trace how far the moisture has spread.
