Caulk that won't stay clean, soft floors, stained ceilings
Mold that comes back after every scrubbing, a spongy spot beside the toilet, or a brown ring on the ceiling below the bath all point to a hidden leak or trapped steam. Call +1-844-326-4757 to reach an independent, licensed and insured bathroom mold contractor in Lexington who finds the water source before opening up tile or drywall.
This line is free: ESS Mold Inspection only routes calls, and independent local contractors do all of the work.
Bathroom mold, explained
Every bathroom mold call falls into one of two buckets. Surface mold on grout and caulk lives on soap film and shower spray, and it scrubs off. The other kind grows behind the tile, inside the wall cavity or under the floor, where a failed shower pan, a leaking valve or a bad wax ring keeps the framing wet for months.
People fight caulk mold for years without winning. When the growth is inside the bead, no spray will reach it; the old silicone gets sliced out with a razor, the gap is dried and treated, and new caulk goes in. Overhead, the ceiling above the shower collects condensation when the fan is too small, gets shut off right away, or blows into the attic rather than through an exterior cap.
Older tub surrounds often hide paper-faced drywall behind the tile, and paper is mold food once water gets past the grout. When the cause is a leak, the remediator and a plumber usually have to coordinate.
Why homeowners call
Expect a few questions up front: where the spots are, whether the floor feels soft, and if there's a ceiling stain on the floor below, so the right type of contractor shows up.
Each contractor in the network runs an independent, licensed and insured business, and it's worth asking to see proof at the door. Some states keep assessment and remediation with separate companies, and the local pro works within that.
Active leaks and ceilings that are sagging or dripping get moved to the front, and a same-day visit is often possible.
Nothing gets opened up until you have a written quote that spells out the demo area, the mold work and what's needed to rebuild.
Expect a moisture meter that reads behind tile, an infrared camera, a borescope for peeking into the wall through a small hole, oscillating cutters and HEPA containment.
Scope of work
Bathroom jobs range from a caulk replacement to a full shower teardown, and most land somewhere between.
Surface growth on grout is cleaned and the grout sealed, while moldy silicone is cut out completely, the joint dried overnight, and new mildew-resistant caulk applied.
When readings behind the tile run high, a section is opened inside plastic containment, the moldy drywall and backer are removed, and the studs are HEPA vacuumed and cleaned. The wall goes back with cement board and a waterproof membrane instead of drywall.
Slow toilet seal leaks rot the plywood under the flange long before anyone notices a soft floor. The work means lifting the toilet, removing the rotten section, drying and treating the joists, and patching with new subfloor.
Slow leaks at the trap or the shutoff valves soak the vanity bottom, which swells and grows mold underneath. The cabinet often has to come out so the wall and floor behind it can be checked.
Ceiling mold from steam is cleaned or the drywall replaced depending on depth, and then the fan gets fixed. Size the fan at roughly 1 CFM per square foot, at least 50 CFM in a small room, vent it to an exterior cap, and let it run around 20 minutes after showering.
One call routes you to a local, independent pro in Lexington who checks for hidden leaks before recommending any demo.
The process
The leak question gets answered before anything is torn out.
Let the dispatcher know where the mold is, whether the floor or tile feels loose, and if anything is showing on the ceiling below. You're then routed to a bathroom-focused remediator serving Lexington.
With an active leak, the contractor frequently gets there that day, bringing moisture meters, an infrared camera and drop cloths.
The visit covers moisture readings around the tub, toilet and vanity, a fan and duct check, and a peek into the wall cavity if readings are high. Any plumbing repair needed is flagged in the written quote so it can be scheduled first.
Request photos of the open cavity, readings taken before rebuild, and whatever workmanship terms the contractor puts on paper. File it with the plumber's invoice.
From the dispatch log
Small spots, bigger causes: here's what usually turns up.
After months of spraying cleaner on the shower caulk, a caller was fed up with black dots coming right back. The contractor found mold rooted inside the silicone and a fan that cleared barely any air. Moisture readings behind the tile were normal.
Outcome: Old silicone cut out and replaced, grout sealed, and the fan upgraded with a 20-minute timer.
The floor beside the toilet felt soft underfoot, and a couple of tiles were rocking. Pulling the toilet showed a failed wax ring and black, crumbling plywood under the flange. The joist below was stained but solid.
Outcome: Subfloor section replaced, joist treated, new flange and wax ring set, then tile repaired.
A property owner got a tenant complaint about dark spotting on the bathroom ceiling right above the shower. The remediator found an undersized fan whose duct stopped in the attic. The drywall was soft in one corner.
Outcome: Damaged ceiling section replaced, new fan sized to the room and vented to an exterior roof cap.
A homeowner called about mold spreading on a kitchen ceiling that sat right below the upstairs bath. Thermal imaging and a meter pointed to a failed shower pan liner leaking into the floor system. A plumber was brought in for the pan.
Outcome: Ceiling below opened and cleaned in containment, joists dried, and the shower pan rebuilt before closing up.
These are composite examples based on common calls to the line, not individual customer reviews.
Before you call
Say where the spots are and the dispatcher will match you with a bathroom specialist working in Lexington.
Call +1-844-326-4757Silicone is porous enough for mold to grow into it, so surface cleaners only hide it for a while. The bead has to be removed entirely, the gap dried, and new caulk laid. Running the fan longer after showers helps keep it from returning.
Watch for tiles that move or sound hollow, grout that keeps cracking, persistent mustiness, or discoloration on the back side of the wall. A contractor can read moisture through the tile with a meter or infrared camera, and look inside with a borescope through a small hole.
Light surface spotting on sound, painted drywall can often be cleaned and then repainted with a mold-resistant bathroom paint. If the drywall is soft, stained through, or the growth covers a large area, that section should be cut out and replaced. Either way, the fan has to be fixed or it'll come back.
A common rule of thumb is about 1 CFM per square foot of floor area, with 50 CFM as the minimum for small bathrooms. Long duct runs and elbows cut real airflow, so the duct should be short, smooth and end at an outdoor cap. A timer switch set for roughly 20 minutes works well.
Often only part of the wall comes off, if the readings show the water stayed in one spot. A failed shower pan or liner, though, usually means removing the floor and lower rows of tile to rebuild it properly. You'll see the demo area in the quote before work begins.
Many bathroom mold jobs start with a leak, so the plumbing has to be repaired before the mold work will last. The remediator will flag the source, and you'll typically need a plumber to fix it before rebuild. Ceiling mold from steam alone usually needs no plumber.
Service area
The line connects Lexington homeowners, landlords and condo owners with independent pros who handle everything from a single moldy caulk joint to a rotted subfloor. Live leaks and ceiling stains below an upstairs bathroom get priority.
Phone +1-844-326-4757 with your address and a short description, and you'll be connected with a bathroom mold pro working in your part of Lexington.
